本页是上海约拿电气有限公司公司为您提供的【供应】FN12-12负荷开关fn12-12/t630-20高压负荷开关厂产品信息和公司介绍,如果您想了解更多关于【供应】FN12-12负荷开关fn12-12/t630-20高压负荷开关厂价格,型号等信息,请联系厂家或给厂家留言。

【供应】FN12-12负荷开关fn12-12/t630-20高压负荷开关厂

企业:上海约拿电气有限公司
价格:面议 / 台
更新:2014-05-15 18:09:21
产地:浙江 - 温州 -
地址:新奉公路2313号

  • 产品详情
  • 公司介绍
  • 提供加工定制:是
  • 品牌:JONAH
  • 型号:FN12-12负荷开关
  • 产品认证:CCC
    

  • 【供应】FN12-12负荷开关fn12-12/t630-20高压负荷开关厂
  • 型号:FN12-12
  • 极数:3极 额定频率:50HZ Hz 额定绝缘电压:42KV
  • 极限分断能力:50KA运行分断能力:20KA kA 
  • 机械寿命:2000次 


  • 货    期:现货
  • 图    纸:有
  • 实 物 图:有
  • 技术支持:工程师电话中解决和支持


  • FN12-12系列产品有:


  • FN12-12   这个是常用型号。
  • FN12-12RA  多一个R字母,代表此负荷开关上装有熔断器底座。
  • FN12-12D  多一个D字母,代表此负荷开关上装有配套的接地装置。
  • FN12-12RD 多两个字母R和D,肯定是代表此开关上装有熔断器底座和接地装置两样。
  • 还有,一般负荷开关开关的型号后面还有带-20KA,这个代表额定断路器。


  •     FN12负荷开关是一款以压气式为主的负荷开关,通过压缩气体来实现灭弧。FN12是额定电压为12KV,额定频率为50Hz的三相


  • 高压开关设备,用于分合负荷电流,闭环电流,空载变压器和电缆充电电流,关合短路电流。 FN12可加装接地可带熔断器,可用


  • 于墙上安装。墙上安装多配CS8-5专用手动操作机构。可侧装,正装,倒装等安装方式,常规是上进线,下出线。可带分励手合电


  • 分,可手和手分。可电动分合等操作方式。现在手合电分常见。FN12现在型号多用FKN12表示,少部分用FN12-12RD/125-31.5


  • 产品简称:详细介绍:
  •  
  • 1 主题内容与适用范围   
  •     本标准规定了交流高压负荷开关(以下简称负荷开关)的术语、产品分类、技术要求、试验方法、检验规则、标志、包装、运


  • 输、贮存等方面的要求。   
  •     本标准适用于额定电压为3~63kV,额定频率为50Hz的户内、户外三相交流电力系统中配电用的负荷开关及其操动机构和辅助


  • 设备。   
  • 2 引用标准   
  •     GB763 交流高压电器在长期工作时的发热   
  •     GB1984 交流高压断路器   
  •     GB1985 交流高压隔离开关和接地开关   
  •     GB2706 交流高压电器动热稳定试验方法   
  •     GB3309 高压开关设备常温下的机械试验   
  •     GB5273 变压器、高压电器和套管的接线端子   
  •     GB7354 局部放电测量   
  •     GB7675 交流高压断路器的开合电容器组试验   
  •     GB11022 高压开关设备通用技术条件   
  • 3 术语   
  • 3.1 负荷开关   
  •     能够在正常电路条件(也可以在规定的过载运行条件)下关合、承载和开断电流以及在规定的异常回路条件(例如短路)下,按


  • 规定的时间承载电流的开关装置。   
  • 3.2 通用负荷开关   
  •     能够进行配电系统中正常发生的直到其额定开断电流的所有关合和开断操作以及能承载和关合短路电流的负荷开关。   
  • 3.3 专用负荷开关   
  •     具有通用负荷开关的一种或几种,但非全部功能的负荷开关。   
  • 3.4 特殊用途负荷开关   
  •     适宜于作为除了对通用负荷开关规定的开合要求以外的负荷开关。例如:电动机负荷开关、单个和背对背电容器组负荷开关


  • 、频繁操作负荷开关、隔离负荷开关等。   
  • 3.5 隔离负荷开关   
  •     在分闸位置,能满足对隔离开关规定的隔离要求的负荷开关。   
  • 3.6 频繁操作负荷开关   
  •     能够开合规定操作频率高于连续供配电系统中所需操作频率的一种负荷开关。   
  • 3.7 电动机负荷开关   
  •     指定用于开合稳定状态和制动条件下电动机的特殊用途负荷开关。   
  • 3.8 单个电容器组负荷开关   
  •     指定用于开合充电电流直到等于其额定单个电容器组开断电流的单个电容器组的一种特殊用途负荷开关。   
  • 3.9 背对背电容器组负荷开关   
  •     指定用于在一个或多个电容器组接到母线或负荷开关的电源侧的情况下,开断电容器组充电电流直到等于其额定背对背电容


  • 器组开断电流的一种特殊用途负荷开关。这种负荷开关应能关合直到等于其额定电容器组关合涌流的相应涌流。    
  • 3.10 有功负载开断电流   
  •     分断有功负载回路时的开断电流。此负载可用电阻器和电抗器相并联来表示。
  • 出口型
  • Offer FN12-12 load switch fn12-12/t630-20 HV load switch factory
    Model: FN12-12
    Poles: 3-pole Rated frequency: 50HZ Hz Rated insulation voltage: 42KV
    Ultimate breaking capacity: 50KA run breaking capacity: 20KA kA
    Mechanical life: 2000




    Delivery: In Stock
    Graph paper:
    Real object diagram:
    Technical Support: Engineer Tel resolve and support




    FN12-12 Series products are:




    FN12-12 is commonly used models.
    A FN12-12RA more than a R letter, on behalf of the fused base load switch.
    FN12-12D more than a D letter on behalf of the grounding device supporting this load switch equipped.
    The FN12-12RD more than two letters R and D, certainly on behalf of this switch fused different base and grounding device.
    Also, after the model of the the general load switch switch there with-20KA, representing the rated circuit breaker.




        The FN12 load switch is a switch-based load puffer compressed gas to the interrupter. FN12 is a rated voltage of 12KV, rated frequency 50Hz three-phase




    High-voltage switchgear for the division and load current, closed-loop current, no-load transformer and cable charging current, to close short circuit current. FN12 installation of ground with the fuse, available




    Installed in the wall. Wall mounted with CS8-5 dedicated manual operating mechanism. Installation of the side-mounted, suits, flip, conventional motivated line under the outlet. With shunt hands to power




    Points, be hand and hand. Electric division and mode of operation. Hands to power common points. FN12 now multi-model in FKN12 small part FN12-12RD/125-31.5




    Product code: Details:
     
    1 Subject Matter and Scope
        This standard specifies the AC HV load switch terminology (hereinafter referred to as load switch), product classification, technical requirements, test methods, inspection rules, signs, packaging, transport




    , Transport, storage and other requirements.
        This standard applies to the rated voltage of 3 ~ 63kV, rated frequency 50Hz indoor, outdoor three-phase AC power system, power distribution, load switch actuator and auxiliary




    Equipment.
    2 reference standards
        The GB763 AC high voltage electrical fever in the long-term work
        GB1984 AC high-voltage circuit breaker
        GB1985 AC high voltage disconnectors and earthing switch
        GB2706 AC high voltage electrical dynamic thermal stability test methods
        GB3309 high-voltage switchgear room temperature mechanical test
        GB5273 transformers, high-voltage electrical terminals and casing
        The GB7354 partial discharge measurements
        GB7675 AC high voltage circuit breaker opening and closing of the capacitor bank test
        GB11022 General technical conditions of high-voltage switchgear
    3 Terms
    3.1 load switch
        Under normal circuit conditions (under the provisions of overload operating conditions) closing, carrying and breaking current specified abnormal circuit conditions (for example, short-circuit),




    Switching means of a predetermined time the current-carrying.
    3.2 Universal load switch
        Normally occurring in the power distribution system until its rated breaking current by the Hopewell breaking operation, as well as be able to carry and close short circuit current, load switch.
    3.3 dedicated load switch
        With one or several of the common load switch, but not the full functionality of the load switch.
    3.4 special purpose load switch
        Suitable as an addition to the requirements of the opening and closing of the provisions of the Universal load switch, load switch. For example: the motor load switch, single and back-to-back capacitor bank load switch




    , Frequent operation load switch, isolation load switch.
    3.5 isolate load switch
        To meet the isolation requirements stipulated load switch disconnectors in the OFF position.
    3.6 frequent operation load switch
        Capable of opening and closing of the provisions of the operating frequency is higher than the and continuous load switch for the desired operating frequency of a power distribution system.
    3.7 motor load switch
        Specify the special purpose load switch for opening and closing of the motor under steady state and braking conditions.
    3.8 single capacitor bank load switch
        Specified for the opening and closing of the charging current until equal Rated single capacitor bank breaking current of single capacitor bank a special purpose load switch.
    3.9 back capacitor load switch
        Specified for the case of one or more capacitors group received the power supply side of the bus bar or load switch, breaking the capacitor charging current until it equals the rated back-to-back capacitor




    Control group breaking current of a special-purpose load switch. This load switch should be closing closing until it is equal to the rated capacitor bank inrush current corresponding inrush current.
    3.10 active load breaking current
        Breaking the active load circuit breaking current. Available load resistor and reactors in parallel.

上海约拿电气有限公司主营低压电器,起动器变频器,软起动器,熔断器,仪器仪表,交流接触器,断路器,电能表,电机起动器,上海变频器,柜体【供应】FN12-12负荷开关fn12-12/t630-20高压负荷开关厂;

上海约拿电气有限公司成立于2003年,座落于上海市奉贤区,致力于电力系统智能化产品的研究、开发、生产及销售为一体的高新技术企业。以专业生产变频器控制柜【VFD】、【VFD-V矢量型变频器】、【VFD-M通用型变频器】,【迷你型/经济型变频器】,【JJR2软起动】、【软起动控制柜】、和阶梯电价国网智能电能表、单三相多费率电能表、单三相导轨表、多功能电能表、单三相电子式预付费电能表(IC卡表)、单三相电子式载波电能表、单相电子式电能表、485电子式电能表、单三相机械表、CGZ866-1F智能载波抄表集中器、HB866大用户管理终端(公用配变终端)、数显表、电力监控仪表、电量变送器、热工智能仪表、温度智能仪表、隔离模块、电量变送器、电流互感器等产品为主。以精确、可靠、节能、环保的智能配电产品满足电力系统各方位的需求。公司一贯坚持“以质量求生存,以科技求发展,以管理出效益”的经营理念,以高品质的电气产品和服务来满足广大客户现在和将来的需求。 约拿产品除在国内广泛使用,还随出口工程项目出口至美国、法国、泰国、俄罗斯、菲律宾、印尼、埃塞俄比亚等诸多国家,产品深受国内外客户好评。公司还专业为各类生产流水线及各类机械设备厂家设计自动化系统和各类配套自动化仪表。同时,多年来为国内外众多钢铁厂、水泥厂、玻璃厂、热电厂及其它各类衡器厂提供了标准和非标的优质仪表,产品和服务质量在业内颇有影响。 多年来,公司引进了先进的技术和严谨的管理方法,引进国内优秀研发人才,其中大专以上科技人员占35%,凭借先进的生产工艺,稳定的产品质量,超前的经营理念,公司已全面通过ISO9001质量管理体系及3C认证,主要产品均通过国家有关检测机构型式试验,并取得证书。为进一步向用户提供质量保证,产品已由中国人民保险公司进行产品质量责任保险承保,并向社会和广大用户郑重提出质量保证及服务承诺。 “优质的产品、先进的技术、尽善尽美的服务”是约拿人的追求目标。面对中国工业电气的发展机遇和挑战,约拿电气制定了新的发展战略规划,快速形成了系统化,规模化的生产模式。在新的环境中,努力创新经营理念,提高管理水平,完善市场网络,加大品牌推广,加速资源整合,全面 约拿电气立足本国,放眼世界,本着互惠互利的原则,愿与社会各界朋友精诚合作,共创 辉煌!诚挚欢迎各方来宾前来参观、洽谈。

  • 产品询价
  • 用户口碑
联系人: 手机:
邮箱: 固定电话:
采购性质: 个人 企业 QQ:
采购数量: 采购地区:
留言内容:
快速选择:
验证码: